Insulation in Windcrest, TX
Crawl space encapsulation and vapor barrier installation in Windcrest typically runs $3,200-$6,800 for a full encapsulation, with most slab-on-grade ranch homes in this mid-century enclave seeing moisture problems that newer San Antonio subdivisions simply don’t face. Because nearly every house here was built between the 1950s and early 1970s with minimal or no under-floor protection, the crawl spaces and pier foundations in Windcrest are unusually susceptible to the humidity that rises from South Texas clay soils. Call (830) 402-5240 for a written price before any work starts.
Why Windcrest Homes Are Different
Windcrest isn’t a patchwork of eras. It’s a single, master-planned residential enclave where nearly every home was built to the same 1950s-1970s specifications, with the same inadequate insulation standards. Original attic insulation was typically 2-3 inches of blown fiberglass or degraded R-11 batts, and exterior wall cavities were often left completely empty. The low-pitched rooflines on these ranch homes create shallow attic clearances, sometimes as little as 18-24 inches at the eaves, which forces material and method choices that wouldn’t apply just a few miles away in newer San Antonio construction.
The San Antonio heat zone pushes attic temperatures past 150°F in summer, and Winter Storm Uri in February 2021 exposed how vulnerable these slab homes with uninsulated walls and garage ceilings are to hard freezes. That combination, extreme heat and occasional severe cold, drives cooling costs that dominate household energy budgets and creates the exact conditions where home performance work pays back fastest. Dispatch and scheduling for Windcrest jobs are coordinated from our San Antonio office, with crews serving the area locally.
Our Main Windcrest Services
Most Windcrest homeowners who call us start with attic work or spray foam, but blown-in remains the practical choice for many of these tight-cavity ranch homes.
Attic Insulation in Windcrest
Attic insulation in Windcrest means working within 18-24 inches of clearance on many of these low-pitch 1960s rooflines, so we often recommend loose-fill fiberglass or cellulose that can be blown into geometry where batt runs simply won’t fit. We air seal top plates, can lights, and penetrations first, then insulate, and we publish before-and-after blower-door numbers so you can verify the result. Attic Insulation in Windcrest

Spray Foam Insulation in Windcrest
Spray foam insulation in Windcrest works exceptionally well for the uninsulated exterior walls common to these mid-century ranch homes, where open-cell or closed-cell foam can be injected or applied to create a continuous air barrier where none existed. We use materials from Icynene and Demilec, among others, and we never lock you into a proprietary product. Every job starts with a written price and ends with a documented photo record. Spray Foam Insulation in Windcrest

Blown-In Insulation in Windcrest
Blown-in insulation in Windcrest is often the only practical solution for attic floors with shallow clearances and irregular joist spacing typical of 1950s-1970s construction. We use Owens Corning and GreenFiber loose-fill products, installed after complete air sealing of the attic floor, with depth markers installed to verify coverage. The blower-door test, a pressurization reading that shows in one number how much air your building envelope is losing, is performed before and after. Blown-In Insulation in Windcrest

What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Crawl Space Encapsulation & Vapor Barrier in Windcrest

Crawl space encapsulation and vapor barrier installation in Windcrest addresses a problem nearly universal to these mid-century ranch homes: pier foundations and minimal slab construction that leave sub-floor areas exposed to South Texas humidity and seasonal moisture migration through clay soils. Because the original construction era predated modern vapor barrier standards, many Windcrest homes have no under-floor protection at all, or what exists has degraded over 50-60 years into brittle, ineffective sheeting. We handle Crawl Space Encapsulation & Vapor Barrier as a complete system, not a product drop-off, and we air seal before we insulate, even in crawl spaces.
Crawl Space Vapor Barrier
Signs you need it
Your floors feel cold or damp in humid months, or you notice a musty odor rising from perimeter access points.
What it costs in Windcrest
A 6-mil to 20-mil vapor barrier installation for a typical Windcrest ranch home runs $1,800-$3,400 depending on access clearance and square footage.
How we do it
We remove debris, grade the soil surface, seam-seal polyethylene sheeting at all overlaps, and mechanically fasten to foundation walls with sealed termination bars.
Crawl Space Encapsulation
Signs you need it
Standing water after rain, visible mold on floor joists, or insulation falling from dampened sub-floor cavities.
What it costs in Windcrest
Full encapsulation with sealed vapor barrier, insulated walls, and conditioned air supply for a Windcrest ranch home typically ranges $3,200-$6,800.
How we do it
We install a sealed ground liner, apply closed-cell foam or rigid board to foundation walls, seal rim joists and penetrations, and add mechanical dehumidification where needed.
What Crawl Space Encapsulation & Vapor Barrier Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Vapor barrier (ground only) | $1,800 - $3,400 |
| Partial encapsulation | $2,600 - $4,800 |
| Full encapsulation with dehumidifier | $3,200 - $6,800 |
How long does crawl space encapsulation take in Windcrest?
Most Windcrest ranch homes take 2-3 days for full encapsulation, with vapor-only jobs completing in one day. Access through the small perimeter openings common to these 1960s slabs can extend setup time. Call (830) 402-5240 for a written timeline with your price.
Will encapsulation help with floor temperature in winter?
Yes, sealed crawl spaces eliminate the 40-60°F air moving beneath uninsulated floors, which was the main reason Windcrest homes felt cold during Winter Storm Uri. We document the before-and-after thermal readings.
Radiant Barrier Installation in Windcrest

Radiant barrier installation in Windcrest targets the specific geometry and climate stress these mid-century ranch homes face: low-pitch rooflines that sit closer to attic insulation, intensifying radiant heat transfer from decking that routinely exceeds 150°F, and cooling systems that work overtime against unshielded roof decks. Because the attic clearances are shallow, the radiant barrier’s reflective surface, usually aluminum foil or metallized film, blocks infrared heat transfer more aggressively than in taller attics where heat has room to dissipate. We install Radiant Barrier Installation systems designed for these tight spaces, with ventilation integration that accounts for the restricted airflow paths.
Attic Radiant Barrier
Signs you need it
Your AC runs continuously after 2 p.m. in July, or second-floor rooms stay 8-12°F hotter than the thermostat setting despite adequate insulation depth.
What it costs in Windcrest
Radiant barrier draped over attic rafters or laid over existing insulation in a typical Windcrest ranch runs $1,400-$2,800.
How we do it
We staple perforated foil to roof rafters or lay it over existing insulation with proper clearance for condensation drainage, then verify attic ventilation isn’t restricted.
Radiant Barrier Roof Deck
Signs you need it
You’re replacing shingles and want the roof deck itself to reject heat before it enters the attic cavity.
What it costs in Windcrest
Deck-applied radiant barrier during roof replacement in Windcrest adds $1,800-$3,200 to the roofing scope for a typical ranch footprint.
How we do it
We apply foil-faced sheathing or liquid-applied low-emissivity coating directly to the roof deck before new shingles go on, with taped seams at all joints.
What Radiant Barrier Installation Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Attic draped radiant barrier | $1,400 - $2,800 |
| Radiant barrier with attic ventilation upgrade | $2,200 - $4,000 |
| Roof deck application during reroof | $1,800 - $3,200 |
Does radiant barrier work with existing insulation?
Yes, it’s designed to complement, not replace, existing insulation by blocking radiant heat that fiberglass doesn’t stop. In Windcrest’s shallow attics, the combination is particularly effective because the barrier sits close to the heat source.
Will radiant barrier make my attic colder in winter?
No, the barrier is bi-directional; it blocks radiant heat transfer from the roof deck downward in summer and reduces heat loss upward in winter. We document seasonal performance expectations in your written scope.
Insulation Removal & Replacement in Windcrest

Insulation removal and replacement in Windcrest is often necessary because the original 1950s-1970s material has simply reached end of life: compressed, moisture-damaged, rodent-contaminated, or settled below effective depth in these low-clearance attics. The uniform construction era means we see the same degradation patterns block by block, original blown fiberglass that has settled to 1-2 inches, batts disintegrated around recessed lights, and vapor barriers that have become moisture traps rather than moisture blocks. We handle Insulation Removal & Replacement with contained extraction, full decontamination if needed, and air sealing before new material goes in.
Attic Insulation Removal
Signs you need it
You can see joists protruding through insulation, smell mustiness from the attic hatch, or find batts crumbling to dust when touched.
What it costs in Windcrest
Removal of existing attic insulation from a typical Windcrest ranch home runs $1,200-$2,400, with disposal and site protection included.
How we do it
We set up negative air containment, remove material with industrial vacuums into sealed bags, and inspect decking for mold or structural issues before any new insulation is specified.
Contaminated Insulation Removal
Signs you need it
Visible rodent droppings, urine staining, or insect debris throughout the insulation layer, or a persistent odor that air fresheners don’t reach.
What it costs in Windcrest
Contaminated removal with full sanitizing and deodorizing in Windcrest typically ranges $2,000-$4,200 depending on contamination extent and attic square footage.
How we do it
We remove all affected material under HEPA containment, apply enzymatic sanitizer to decking and joists, and provide photo documentation of the cleaned cavity before replacement begins.
What Insulation Removal & Replacement Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Standard attic insulation removal | $1,200 - $2,400 |
| Contaminated insulation removal + sanitizing | $2,000 - $4,200 |
| Removal + replacement with air sealing | $3,400 - $6,200 |
Do I have to leave during insulation removal?
No, our contained extraction keeps living spaces isolated, though we recommend pets be kept elsewhere for the day. We send you the photo record of the cleaned attic before replacement material is loaded.
How do I know if my old insulation is hazardous?
Pre-1990 vermiculite may contain asbestos; we test before disturbing it. Other contamination, rodent or moisture, is visible and odor-detectable. Call (830) 402-5240 and we’ll inspect with a written assessment.
Attic Air Sealing in Windcrest

Attic air sealing in Windcrest is the single most cost-effective upgrade for these mid-century ranch homes because the original construction left hundreds of linear feet of top plates, electrical penetrations, and duct boots completely unsealed, creating a direct path for 150°F attic air to press conditioned air out of the house. The blower-door test, a pressurization reading that shows in one number how much air your building envelope is losing, typically reveals 3,500-5,500 CFM50 in an unsealed Windcrest ranch, meaning the house replaces its entire air volume every 15-20 minutes in extreme conditions. We perform Attic Air Sealing as a standalone service or as the mandatory first step before any insulation is added.
Top Plate & Penetration Sealing
Signs you need it
Dust streaks around ceiling fixtures, rooms that won’t maintain temperature despite adequate insulation depth, or high utility bills with no equipment explanation.
What it costs in Windcrest
Top plate and penetration sealing for a typical Windcrest ranch runs $1,600-$2,800, with blower-door verification included.
How we do it
We seal all wall top plates with fire-rated caulk or foam, gasket electrical boxes, and foam-seal plumbing and wiring penetrations, then retest with the blower door to quantify reduction.
Can Light & Duct Boot Sealing
Signs you need it
Hot air pouring from ceiling vents when the AC is off, or visible gaps around recessed light housings that aren’t IC-rated.
What it costs in Windcrest
Can light sealing with proper covers and duct boot sealing with mastic runs $800-$1,600 for a typical Windcrest home with 6-10 fixtures.
How we do it
We install fire-rated covers over non-IC can lights, seal with high-temperature caulk, and apply mastic and mesh to all flex duct connections at the ceiling plane.
What Attic Air Sealing Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Top plate & penetration sealing | $1,600 - $2,800 |
| Can light & duct boot sealing | $800 - $1,600 |
| Full attic air sealing package | $2,400 - $4,200 |
Can air sealing alone lower my bill?
Yes, 15-30% reductions are common in Windcrest’s leaky ranch homes, with the blower-door test providing the before-and-after proof. We publish your numbers in the job documentation.
Is air sealing required before adding insulation?
Under our Haven Standard, yes, we will not blow insulation over an unsealed attic floor because it buries the leaks and makes them impossible to address later. The written scope specifies the sealing sequence.
Wall Insulation in Windcrest

Wall insulation in Windcrest addresses what is often the largest uninsulated surface in these homes: exterior walls that were built with empty cavities as standard practice in the 1950s-1970s construction era. The slab-on-grade construction means there’s no basement buffer, so uninsulated walls transfer heat directly from soil to siding to interior, and Winter Storm Uri proved how fast these homes lose heat when the envelope fails. We install Wall Insulation using methods designed for finished interiors, minimizing disruption to original plaster or drywall that is itself part of these homes’ character.
Injection Foam Wall Insulation
Signs you need it
Walls that are hot to the touch in summer, cold in winter, or rooms with exterior walls that never reach thermostat temperature despite good attic performance.
What it costs in Windcrest
Injection foam for exterior walls in a typical Windcrest ranch runs $2,800-$5,200 depending on wall square footage and cavity condition.
How we do it
We drill 5/8-inch holes through exterior siding or interior drywall at stud spacing, inject slow-rise foam that fills without bowing, then patch and match finish.
Drill & Fill Wall Insulation
Signs you need it
You’re remodeling a room and want to insulate before closing walls, or you’ve confirmed empty cavities with a thermal imaging inspection.
What it costs in Windcrest
Drill and fill with dense-pack cellulose for open walls in Windcrest ranges $1,800-$3,400 for a typical room or addition.
How we do it
We remove interior drywall or access through exterior sheathing, dense-pack cellulose to 3.5 pounds per cubic foot for no-settle performance, and install smart vapor retarders where needed.
What Wall Insulation Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Injection foam (exterior walls, finished) | $2,800 - $5,200 |
| Drill & fill cellulose (open walls) | $1,800 - $3,400 |
| Exterior wall insulation with air sealing | $3,400 - $6,000 |
Will injection foam damage my walls?
No, slow-rise formulations are specified for existing walls and won’t bow studs or crack plaster. We pressure-limit the injection and verify fill with thermal imaging.
Can you insulate walls without removing drywall?
Yes, injection foam and dense-pack cellulose both access cavities through small holes that are patched and painted to match. We specify the patch method in your written scope before work starts.
Attic Cleaning & Rodent Proofing in Windcrest

Attic cleaning and rodent proofing in Windcrest is frequently needed because 50-60 years of original construction creates multiple entry points that rodents exploit, and the settled, degraded insulation provides ideal nesting material. The uniform roofline geometry means we see the same entry patterns repeatedly: gaps at fascia boards, unsealed plumbing vents, and construction tolerances in the low-pitch eaves that have widened with thermal cycling. We perform Attic Cleaning & Rodent Proofing as a complete system, removal, sanitizing, exclusion, and documentation, not a surface sweep that leaves the problem.
Attic Cleanout
Signs you need it
Visible rodent nests, scattered insulation, stored items contaminated with droppings, or a smell that enters living spaces through recessed lights.
What it costs in Windcrest
Complete attic cleanout with debris removal and disposal for a typical Windcrest ranch runs $800-$1,600.
How we do it
We remove all contaminated material and debris under negative air pressure, HEPA-vacuum exposed surfaces, and bag everything for off-site disposal with documentation.
Rodent Proofing & Exclusion
Signs you need it
Scratching sounds in walls or ceiling, visible droppings in attic or garage, or recurring rodent activity after previous trapping efforts.
What it costs in Windcrest
Rodent proofing with metal exclusion, sealant, and one-way exits for a typical Windcrest home ranges $1,200-$2,400.
How we do it
We identify all entry points with inspection cameras, seal with rodent-proof materials (not foam alone), install one-way exits if active, and provide the photo record of every sealed location.
What Attic Cleaning & Rodent Proofing Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Attic cleanout only | $800 - $1,600 |
| Rodent proofing & exclusion | $1,200 - $2,400 |
| Cleanout + proofing + sanitizing | $2,200 - $4,000 |
How do I know rodents are gone before you seal?
We install one-way exits that let them leave but not re-enter, then monitor with inspection cameras for 3-5 days before permanent sealing. The photo record shows the empty cavity.
Will rodent proofing keep all pests out?
It eliminates rodent entry at the sealed points; ongoing maintenance of the building envelope prevents new gaps from developing. We note vulnerable areas in your documentation for annual inspection.
Home Energy Audit in Windcrest

A home energy audit in Windcrest provides the documentation that these research-oriented homeowners need before committing to envelope work, quantifying exactly how much conditioned air the house loses and where the thermal defects are concentrated. Because the housing stock is so uniform in era and construction type, audit results in Windcrest are highly predictive, we know what we’ll find, but the homeowner deserves the numbers in writing before any work is specified. We conduct Home Energy Audit visits that include blower-door testing, thermal imaging, and a written priority list with prices for each recommended measure.
Blower Door Test
Signs you need it
You want to quantify air leakage before deciding on insulation scope, or you’ve completed work elsewhere and want to verify the contractor’s claims.
What it costs in Windcrest
A standalone blower-door test with written report for a Windcrest ranch home runs $350-$550; it’s credited toward work if you proceed within 90 days.
How we do it
We install a calibrated fan in an exterior door, depressurize to -50 Pascals, measure CFM50, and identify leakage locations with smoke pencils and thermal imaging.
Thermal Imaging Inspection
Signs you need it
You suspect missing wall insulation, want to verify attic coverage uniformity, or need to document a defect for an insurance or warranty claim.
What it costs in Windcrest
Thermal imaging as part of a full audit or standalone inspection in Windcrest ranges $250-$450, with images delivered in a dated report.
How we do it
We scan all building envelope surfaces with a calibrated infrared camera, noting Delta-T readings at anomalies, and mark locations on floor plans for remediation quoting.
What Home Energy Audit Costs in Windcrest
| Item | Typical range in Windcrest |
|---|---|
| Blower door test with report | $350 - $550 |
| Thermal imaging inspection | $250 - $450 |
| Full home energy audit | $450 - $750 |
What does a home energy audit include in Windcrest?
A full audit includes blower-door test, thermal imaging, insulation inspection, and duct leakage testing with a written priority list and priced recommendations. We schedule 2.5-3 hours on site.
Is the audit cost applied to the work?
Yes, the full audit fee is credited to any Envelope work you schedule within 90 days. The written quote specifies the credit; Haven Standard Clause 1 requires the price in writing before work starts.
Brands We Service in Windcrest

We source insulation and air sealing materials from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber, with no proprietary product lock-in. For Windcrest jobs, we stock Owens Corning loose-fill fiberglass and Icynene open-cell foam locally, enabling next-day material availability for most projects. See our brands for full specifications.
Pricing for Insulation in Windcrest, TX
| Service | Typical range in Windcrest |
|---|---|
| Crawl space vapor barrier | $1,800 - $3,400 |
| Full crawl space encapsulation | $3,200 - $6,800 |
| Attic radiant barrier | $1,400 - $2,800 |
| Radiant barrier roof deck (during reroof) | $1,800 - $3,200 |
| Attic insulation removal | $1,200 - $2,400 |
| Contaminated insulation removal + sanitizing | $2,000 - $4,200 |
| Top plate & penetration air sealing | $1,600 - $2,800 |
| Full attic air sealing package | $2,400 - $4,200 |
| Injection foam wall insulation | $2,800 - $5,200 |
| Attic cleanout | $800 - $1,600 |
| Rodent proofing & exclusion | $1,200 - $2,400 |
| Full home energy audit | $450 - $750 |
Prices in Windcrest push toward the higher end when access is limited by the shallow attic clearances common to these 1960s ranch homes, or when contaminated material requires HEPA containment. Every job begins with a written price before any work starts, under Haven Standard Clause 1, with no exceptions.
Neighborhoods We Serve in Windcrest

We work throughout Windcrest’s original master-planned boundaries and surrounding blocks, with crews typically arriving within scheduled windows coordinated from our San Antonio office. Most Windcrest appointments are available within 2-4 business days for non-emergency work.
- Windcrest Estates
- Midway Hills
- Windcrest Terrace
- Rolling Oaks
- Woodlake area
Service Area - Cities Near Windcrest
Envelope Insulation Co. serves homeowners throughout the San Antonio metro, with regular work in Schertz, TX, Cibolo, TX, Universal City, TX, and Selma, TX. Scheduling and material coordination for all locations run through our San Antonio office, with local crews dispatched to each job site.
Serving Windcrest, TX - Our Local Coverage Area
We’re based in the Windcrest area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Windcrest
We typically schedule Windcrest appointments within 2-4 business days for standard work; emergency calls for active leaks or post-storm damage are triaged same-day when possible. A live person answers 24/7 to coordinate.
Most attic and wall insulation in Windcrest does not require a permit, but crawl space encapsulation with electrical dehumidifier installation may trigger a mechanical permit. We verify requirements before work starts and include any permit in the written price.
Windcrest’s original master-planned areas have minimal active HOA oversight, but we provide written scope documentation and photo records that satisfy any architectural review requirements. We coordinate directly with property managers when needed.
Ready to see what your home is actually losing? Call (830) 402-5240 for a free estimate with a written price before any work starts. We’ll bring the blower door, the thermal camera, and the Haven Standard documentation that shows you exactly what you’re paying for.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Windcrest Customers Say
"Crawl space encapsulation done properly. Photographs of the vapour barrier at every seam, and the damp smell in the hallway is gone."
- Ainsley P."They air-sealed the attic floor before insulating and showed me the blower-door number before and after. The upstairs is finally the same temperature as downstairs."
- Marisol D."Turned up on time, protected the hallway, and the written scope matched what was actually done."
- Bruno S.